更改西门子SX1开机动画

yebi1985

Welcome to the startup.mbm tutorial for Siemens SX1 @ by JiDo!
Translated to CN by yebi1985.
Target of this tutorial:
Making your own Bootscreen (startup.mbm) that appears after entering the PIN into your SX1
What you need:
MBM Wizard
WinHex
Some Imaging Software (Paint should do it, better use Photoshop)
a WinSwup-firmware for the SX1
Inventory:
Part 1: Creating a new, fitting startup_new.mbm.
Part 2: Adjusting the size of the startup_new.mbm to the size of the original startup.mbm.
Part 3: Replacing the original startup.mbm with the startup_new.mbm with WinHex inside the primary memory of the WinSWUP firmware
ATTENTION: By applying a WinSWUP Firmware to your SX1 you will lose your warranty. If you don’t know what you are doing, LEAVE IT. Too bad for you precious SX1

Part 1
Create a new Picture within your favourite imaging software, size 176x208 Pixels.

欢迎您查看更改西门子SX1开机动画(startup.mbm)教程BY jido      翻译:yebi1985
本教程目标：
制作您自己的Bootscreen （ startup.mbm ）
您需要：
MBM Wizard
WinHex
图象处理软件（Paint应该可以做到这一点，最好是用Photoshop ）
a WinSwup-firmware for the SX1
过程：
第1部分：创建一个新的，合适的startup_new.mbm 。
第2部分：调整大小,startup_new.mbm要小于原来startup.mbm 。
第3部分：取代原有startup.mbm,用WinHex修改startup_new.mbm的进程信息,最后WinSWUP刷机.
注意：通过WinSWUP对您的SX1刷机,您将失去您的保修服务。如果您不知道自己在做什么，请离开。浪费了你宝贵的SX1!
第1步
用PS创建一个新的你最喜爱的图片，大小176x208像素。

                               
登录/注册后可看大图

Save this file as .bmp.
Change to MBM
Wizard and load the bmp-file 12 times with the attribute /c8. You have to load it 12 times or otherwise your SX1 will crash at startup. /c8 is important, because with /c16 or c/24 the SX1 will use a different colour palette and the colours will not be displayed right.
Instead of loa由于非常钦佩楼主，不得不说声好！ one picture 12 times, you can create an animation containing 12 frames, none more and none less!

将此文件保存为xxx.bmp
换到MBMWizard加载图像文件并生成12张8位的bmp 。您必须这样做,不然您SX1将在启动时崩溃。 8位是重点!因为c/16或c/24的,SX1的调色板和颜色将不会显示正确的。
您可以创建一个包含12帧动画，不多不少

                               
登录/注册后可看大图

Save the new mbm-file under the name "startup_new.mbm".
Now check the size of the "startup_new.mbm". It must be no bigger than your original startup.mbm. Most certainly it will not be the same size as the original startup.mbm so we will adjust the size in part 2.
Part 2
Open WinHex and load the original startup.mbm together with the startup_new.mbm you just created. Scroll both files down to the end. Now subtract the value in the last line of the new file from the old file.

保存新的mbm文件“ startup_new.mbm ” 。
现在检查“ startup_new.mbm ”大小 。它一定不能超过原来的startup.mbm 。肯定不会是和原始startup.mbm一样大 ，所以我们接下来一步就是调整大小。
第2步
打开WinHex加载startup.mbm同您刚刚创建的startup_new.mbm。查看最底层。用startup.mbm数值减startup_new.mbm的数值,如下图

                               
登录/注册后可看大图

Here this is 197888 - 171520 = 26368
Note that value, you will need it soon.
Activate the startup_new.mbm window in WinHex.
1) Mark the last hex value.
2) Now, in the menu choose "Edit --> Paste Zero Bytes”


这里是197888 - 171520 = 26368
记住这个数,等会会用到.
点击startup_new.mbm窗口。
1 ）标记十六进制值。
2 ）现在，在菜单中选择"Edit --> Paste Zero Bytes"

                               
登录/注册后可看大图

3) Enter the value from your subtraction.
4) When asked "Append to the end of the File?" click Yes!

3 ）输入刚刚相减得到的数值。
4 ）当问及"Append to the end of the File?"单击yes!

                               
登录/注册后可看大图

Now compare the two files. The end of file has to be at exactly the same point in both files. Here, there are three Hex values too much. Delete them to make the startup_new.mbm exactly the same size as the original startup.mbm. Should there be too few hex values, add some.
This is how it should look like:

现在，比较两个文件。最底下一层的数值就都一样了。数值多就删除它们，使startup_new.mbm完全一样大小的原始startup.mbm 。如果少了数值，就增加一些。
最后看起来应该像这样：

                               
登录/注册后可看大图

Save the startup_new.mbm.
Part 3
Now start the WinSWUP firmware. I recommend the v15 International, because when using a different one, you have to know the exact size of the old startup.mbm of your version. Other versions have different startup animations which differ in size. In WinHex choose "Tools --> RAM Editor" and select "Sx1-international-uk-de-it_15_0001_service" respectively the name of your Firmware. From the following popup window select "Primary Memory".

保存startup_new.mbm 。
第3步
现在开始刷机。我建议SX1-v15中文版。在WinHex选择“工具” "内存编辑器"并选择" Siemens Sx1 SVN15 (Admin Mod).exe" 下的内存。
在弹出的窗口中选择 "Primary Memory".

                               
登录/注册后可看大图

  
Change to the first line of the original startup.mbm. Mark the first two lines and select from the menu "Edit --> Copy Block --> Hex Values".
点击原始startup.mbm窗口 。标记头两行，并从菜单中选择"Edit --> Copy Block --> Hex Values".

                               
登录/注册后可看大图

Change to the firmware window and select  "Search --> Find Hex Values". In the opening dialogue, paste the hex values of the original startup.mbm via CTRL-V. Press OK and you are at the beginning of the original startup.mbm within the firmware RAM.
点击切换到winhex主窗口并选择 "Search --> Find Hex Values".在弹出的对话框里，粘贴原始startup.mbm十六进制值。按下OK 。

                               
登录/注册后可看大图

  
Change to the startup_new.mbm. Mark the whole file with CTRL-A  and copy it with CTRL-C.
Go back to the Firmware window and place the Cursor at the beginning of the original startup.mbm. Now, from the menu select "Edit --> Clipboard Data --> Write". Answer the following comment „The clipboard data will be written at offset XXXXXX“ with yes.
Now you can close WinHex and change to the WinSwup-Update of your firmware and leave only VAR (Z2) checked, uncheck all other options.
切换到startup_new.mbm窗口 。Ctrl+A全选再Ctrl+C复制 。
返回主程序界面。从菜单中选择"Edit --> Clipboard Data --> Write". 弹出“The clipboard data will be written at offset XXXXXX”选'是'。
关闭WinHex,启动刷机程序Siemens Sx1 SVN15 (Admin Mod).exe只选var（ Z2 ）。

                               
登录/注册后可看大图

Now press Start and the modified Firmware is being flashed to the phone. Since you are only writing Var (Z2) this should not take long.
Have fun trying it.
JiDo & yebi1985
No warranty whatsoever can be given to the above descriptions. If you are tempering with your phones software, you do so on your own behalf. Neither the author nor the translator can be held responsible for any damage to your phone.

                                                                   现在，刷机!!!!!

                                                                JiDo ＆ yebi1985
对上述教程不做任何担保。如果您是锻炼你的手机，您这样做只代表您自己。无论是作者还是译者对任何损害到您的手机的操作都不承担责任。

又及~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~本人英语水平有限,翻译错误之处在所难免,大家就结合图片自己摸索吧.
需要补充和更正之处,就跟帖指正.

jimmy52114258

bu dong

segalgx

感谢分享

yingxinlei

感谢分享啊

slinglingfa

感觉好麻烦   
我一般用MBMTOOL改好之后  直接用APATCHER或EDITORZ生成补丁   比较方便

amdyanwei

看不怎么明白啊